国外无损检测标准

2022-08-05 10:51:47 作者：工业小南点来源：工业小南点分享至：

欧洲标准化委员会标准：

EN 1290:1998 焊缝无损检测焊缝的磁粉检验

Non-destructive examination of welds-Magnetic particle examination of welds

EN 1291:1998 焊缝无损检测焊缝的磁粉检验验收等级

Non-destructive examination of welds-Magnetic particle testing of welds-Acceptancelevels

EN 1330/5:1998 无损检测词汇涡流检测所用术语

Non-destructive testing-Terminology-Part 5:Terms used in Eddy current testing

EN 1369:1996 铸件磁粉检查

EN 1711:2000 焊缝无损检测基于复平面分析的焊缝涡流检测

Non-destructive examination of welds-Eddy current examination of welds by complexplane analysis

EN 1956: 无损检测渗透检测和磁粉检测

EN 1971: 铜和铜合金的涡流检测

EN 2857/1: 磁粉检测总则

EN 2857/2: 检查要求

EN ISO 3059:2001 无损检测渗透检测和磁粉检测观察条件

Non-destructive testing-Penetrant testing and magnetic particle testing-Viewingconditions(ISO 3059:2001)

EN ISO 9934-1:2001/A1:2003 无损检测磁粉检测第1部分：一般原理

Non-destructive testing-Magnetic particle testing-Part 1:General principles(ISO9934-1:2003)

EN ISO 9934-2:2002 无损检测磁粉检测第2部分：检测介质

Non-destructive testing-Magnetic particle testing-Part 2:Detection media(ISO9934-2:2002)

EN ISO 9934-3:2002 无损检测磁粉检测第3部分：设备

Non-destructive testing-Magnetic particle testing-Part 3:Equipment(ISO9934-3:2002)

EN 10228/1:1999 磁粉检查

EN 10246/1:1996 无缝与焊接（埋弧焊除外）铁磁性钢管的自动电磁检测-验证液压密封性

EN 10246/2:2000 无缝与焊接（埋弧焊除外）奥氏体和奥氏体铁素体钢管的自动涡流检测-验证液压密封性

EN 10246/3:1999 无缝与焊接（埋弧焊除外）钢管的自动涡流检测-探伤

EN 10246/4:1999 无缝铁磁性钢管的自动全圆周磁传感器/漏磁检测-检测横向缺陷

EN 10246/5:1999 无缝与焊接（埋弧焊除外）铁磁性钢管的自动全圆周磁传感器/漏磁检测-检测纵向缺陷

EN 10246/12:2000 无缝与焊接铁磁性钢管的磁粉检测-检测表面缺陷

EN 10246/18:2000 无缝与焊接铁磁性钢管管端面的磁粉检测-检测层状缺陷

EN 12084:2001/A1:2003 无损检测涡流检测一般原理和指南

Non-destructive testing-Eddy current testing-General principles and guidelines

EN 13860-1:2003 无损检测涡流检测设备性能与验证第1部分：仪器性能与验证

Non-destructive testing-Eddy current examination-Equipment characteristics andverification-Part 1:Instrument characteristics and verification

EN 13860-2:2003 无损检测涡流检测设备性能与验证第2部分：探头性能与验证

Non-destructive testing-Eddy current examination-Equipment characteristics andverification-Part 2:Probe characteristics and verification

EN 13860-3:2003 无损检测涡流检测设备性能与验证第3部分：系统性能与验证

Non-destructive testing-Eddy current examination-Equipment characteristics andverification-Part 3:System characteristics and verification

EN WI 45:2002 涡流检测设备

03014008发表于 2008-11-812:54

美国标准：

ASTM A275/A275M-1998 钢锻件磁粉检验方法(A-1) Test Method for Magnetic Particle Examination of SteelForgings

ASTM A340-2001 与磁化试验有关的符号和定义的术语

Terminology of Symbols and Definitions Relating to Magnetic Testing

ASTM A341/A341M-1995 用直流磁导计和弹道学法测定材料直流磁性能的试验方法

Test Method for Direct Current Magnetic Properties of Materials Using D-CPermeameters and the Ballistic Test Methods

ASTM A342-1995 弱磁材料导磁率的试验方法 Test Methods forPermeability of Feebly Magnetic Materials

ASTM A450-76 钢管涡流检测

ASTM A456/A 456M-1999 大型曲轴锻件磁粉检验的标准规范

Standard Specification for Magnetic Particle Examination of Large CrankshaftForgings

ASTM A556-65 无缝碳素钢管涡流检测

ASTM A596/A596M-1995 用弹道学法和环形试样测定材料直流磁性能的试验方法

Test Method for Direct-Current Magnetic Properties of Materials Using theBallistic Method and Ring Specimens

ASTM A772/A772M-1995 利用正弦电流测定材料交流磁导率的试验方法

Test Method for A-C Magnetic Permeability of Materials Using Sine Current

ASTM A894/A894M-1995 磁性材料饱和磁化的试验方法 Test Method for Saturation Magnetization of Magnetic Materials

ASTM A 903/A 903M-1999 钢铸件磁粉和液体渗透检验的表面验收标准

Steel Castings, Surface Acceptance Standards, Magnetic Particle and LiquidPenetrant Inspection

ASTM A966-1996 用交流电流检验钢锻件磁粉检验方法

Test Method for Magnetic Particle Examination of Steel Forgings UsingAlternating Current

ASTM A977-1997 使用磁滞曲线绘制仪测试高矫顽磁性永磁材料磁性能的标准试验方法

Standard Test Method for Magnetic Properties of High-Coercivity PermanentMagnet Materials Using Hysteresigraphs

ASTM B193-1995 导电材料电阻率的测试方法 Test Method for Resistivityof Electrical Conductor Materials

ASTM B244-1997 用涡流仪测量铝阳极化层及其它非磁性金属基体上绝缘涂层的厚度

Measurement of Thickness of Anodic Coatings on Aluminum and of OtherNonconductive Coatings on Nonmagnetic Basis Metals with Eddy-CurrentInstruments

ASTM B342-70 材料导电率的涡流测量方法

ASTM B499-1996 磁性金属基体上非磁性涂层厚度测量的试验方法：磁性法(B-8)

Test Method for Measurement of Coating Thicknesses by the Magnetic Method:Nonmagnetic Coatings on Magnetic Basis Metals

ASTM B529-70 非磁性金属上非导电层厚度的涡流测量方法

ASTM B530-1996 用磁性法测量磁性和非磁性基体上的电镀镍层厚度的试验方法

Test Method for Measurement of Coating Thicknesses by the Magnetic Method:Electrodeposited Nickel Coatings on Magnetic and Nonmagnetic Substrates

ASTM B554-71 非金属上金属涂层厚度测量的推荐方法

ASTM C1238-1997 地下通道金属探测器的安装 Installation ofWalk-Through Metal Detectors

ASTM C1269-1997 内穿过式金属探测器操作灵敏度设置调整的标准规程

Standard Practice for Adjusting the Operational Sensitivity Setting of In-PlantWalk-Through Metal Detectors

ASTM C1309-1997 内穿过式金属检测器性能评定的标准规程

Standard Practice for Performance Evaluation of In-Plant Walk-Through MetalDetectors

ASTM D1186-93 铁基体上非磁性薄膜的干膜厚度无损测量方法

ASTM D1400-94 非铁金属基体上非导电覆盖层干膜厚度无损测量方法

ASTM D4166-1999 数字磁强仪测量非磁性材料厚度的试验方法

Test Method for Measurement of Thickness of Nonmagnetic Materials by Means of aDigital Magnetic Intensity Instrument

ASTM D6639-2001 地下勘察用频域电磁法的标准指南

Standard Guide for Using the Frequency Domain Electromagnetic Method forSubsurface Investigations

ASTM E45 确定钢中夹杂物含量的标准方法

ASTM E109-76 干粉法磁粉检验

ASTM E125-1997(2003) 铸铁件磁粉检验参考照片 Reference Photographsfor Magnetic Particle Indications on Ferrous Castings

ASTM E138-76 湿法磁粉检验

ASTM E215-2001 铝合金无缝管电磁检验的标准化设备

Standardizing Equipment for Electromagnetic Examination of SeamlessAluminum-Alloy Tube

ASTM E243-2001 铜及铜合金管电磁(涡流) 检测规程

Practice for Electromagnetic (Eddy-Current) Examination of Copper andCopper-Alloy Tubes

ASTM E268-84a 电磁检测术语定义

ASTM E269-84a 磁粉检验术语定义

ASTM E309-95(2001) 钢管制品磁饱和法涡流检查规程

Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation

ASTM E376-2003 用磁场或涡流(电磁的)检测法测量涂层厚度的规程

Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current(Electromagnetic) Test Methods

ASTM E426-2001 奥氏体不锈钢及类似合金无缝和焊接管制品的电磁(涡流) 检验

Electromagnetic (Eddy-Current) Examination of Seamless and Welded TubularProducts, Austenitic Stainless Steel and Similar Alloys

ASTM E566-2001 黑色金属电磁(涡流)分选 Electromagnetic (Eddy-Current) Sorting of Ferrous Metals

ASTM E570-2001 铁磁性钢管制品漏磁检验的规程

Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products

ASTM E571-2001 镍和镍合金管制品电磁(涡流) 检验

Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy TubularProducts

ASTM E690-2001 非磁性热交换器管现场电磁(涡流)检验

In Situ Electromagnetic (Eddy-Current) Examination of Nonmagnetic HeatExchanger Tubes

ASTM E703-2001 有色金属电磁(涡流)分选规程

Practice for Electromagnetic (Eddy-Current) Sorting of Nonferrous Metals

ASTM E709-2001 磁粉检验指南 Guide for Magnetic ParticleExamination

ASTM E977-2005 导电材料热电分选技术规程

Practice for Thermoelectric Sorting of Electrically conductive Materials

ASTM E1004-2002 用电磁(涡流)法测定电导率的标准规程

Standard Practice for Determining Electrical Conductivity Using theElectromagnetic (Eddy-Current) Method

ASTM E1033-2001 居里点温度以上用电磁(涡流)法检查F 型连续焊(CW) 铁磁性管的技术规程

Practice for Electromagnetic(Eddy-Current) Examination of Type F-ContinuouslyWelded(CW) Ferromagnetic Pipe and Tubing Above the Curie Temperature

ASTM E1312-2001 居里点温度以上铁磁性圆柱棒电磁(涡流) 检查技术规程

Practice for Electromagnetic(Eddy-Current) Examination of FerromagneticCylindrical Bar Product Above the Curie Temperature

ASTM E1444-2005 磁粉检验标准规程 Standard Practice for MagneticParticle Examination

ASTM E1571-2001 铁磁性钢丝绳电磁检验规程

Practice for Electromagnetic Examination of Ferromagnetic Steel Wire Rope

ASTM E1606-2001 电工用铜质再拉棒电磁(涡流) 检查技术规程

Practice for Electromagnetic(Eddy-Current) Examination of Copper Redraw Rod forElectrical Purposes

ASTM E1629-1996(2001) 测定绝对式涡流探头阻抗的规程

Practice for Determining the Impedance of Absolute Eddy Current Probes

ASTM E2096-2005 使用远场涡流技术现场检查铁磁性热交换器管的技术规程

Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes UsingRemote Field Testing

ASTM E2261-2003 交流电场测量技术的焊缝检测规程

Practice for Examination of Welds Using the Alternating Current FieldMeasurement Technique

ASTM E2297-2004 液体渗透和磁粉方法用UV-A与可见光源及强度计的指南

Guide for use of UV-A and Visible Light Sources and Meters used in the LiquidPenetrant and Magnetic Particle Methods

ASTM E2337-2004 互感电桥应用于锅炉管壁测厚的指南

Guide for Mutual Inductance Bridge Applications for Wall ThicknessDeterminations in Boiler Tubing

ASTM E2338-2004 用不带标准参考覆盖层的适当涡流传感器表征覆盖层特性的规程

Practice for Characterization of Coatings Using Conformable Eddy-Current Sensorwithout Coating Reference Standards

ASTM F673-1990(1996) 用非接触涡流仪测量半导体膜片电阻率的试验方法(F-1)

Test Methods for Measuring Resistivity of Semiconductor Slices or SheetResistance of Semiconductor Films with a Noncontact Eddy-Current Gage

ASTM G96-90(1996) 固定设备在线腐蚀监测指南（电学和电磁学方法）

ASME Boiler & Pressure Vessel Code(ASME锅炉压力容器规范)第V卷《无损检测》2004版，第7篇“磁粉检测”

MIL-M-6867C-69 磁性检验设备

MIL-I-6868E-76 磁粉检验方法(INDT,85-4)

MIL-HDBK-728/4(92) 磁粉检验

MIL-HDBK-728/2(92) 涡流检验

MIL-STD-288(57) 测定变形奥氏体钢磁导率的程序

MIL-STD-1537B(88) 用涡流电导率测试法检验铝合金热处理质量

MIL-STD-2032(90) 美国海军舰船用热交换器管涡流检验

MIL-M-6867C(69) 磁粉检验设备

MIL-I-83387A(87) 磁橡胶检查方法

MIL-P-85585(82) 无屏蔽单线圈绝对测量的涡流探头

BAC 5424 (美国波音公司)磁粉检验

BAC 5963 涡流检验

DPS 4.704 (美国麦道公司)磁粉检验

DPS 4.704-1 磁粉检验--返修

DPS 4.704-2 磁粉检验--适用性

DPS 1.05 涡流法测电导率--设备与方法

03014008发表于 2008-11-812:55

日本标准：

JIS C2501-1998 永久磁铁试验方法 Methods of test for permanentmagnet

JIS G 0565-1992 铁磁性材料磁粉检验方法及磁粉显示等级 (INDT,84-2 1982年版)

METHOD FOR MAGNETIC PARTICLE TESTING OF FERROMAGNETIC MATERIALS ANDCLASSIFICATION OF MAGNETIC PARTICLE INDICATION

JIS G 0568-1993 钢制产品的环绕线圈法涡流检测

Method for eddy current testing of steel products by encircling coil technique

JIS G 0583-2004 钢管的涡流检验方法 Eddy current examination ofsteel pipes and tubes

JIS H 0502-1986 铜及铜合金管的涡流检测方法

METHOD OF EDDY CURRENT TESTING FOR COPPER AND COPPER ALLOY PIPES AND TUBES

JIS H 0505-1975 有色金属材料的电阻率及导电率测定方法

Measuring methods for electrical resistivity and conductivity of non-ferrousmaterials

JIS H 0515-1992 钛管的涡流检验 Eddy current inspection oftitanium pipes and tubes

JIS H 0601:62 锗的电阻率测定方法

JIS H 0602:95 硅单晶及硅薄片的四探针法电阻率测定方法

JIS Z 2314-1991 涡流试验仪器性能特性试验方法

Test methods for performance characteristics of eddy current testinginstruments

JIS Z 2315-1991 涡流探伤系统性能特性试验方法

TEST METHODS FOR PERFORMANCE CHARACTERISTICS OF EDDY CURRENT FLAW DETECTINGSYSTEM

JIS Z 2319-1991 漏磁试验方法 Methods for magnetic leakageflux testing

JIS Z 2321-1993 用于磁粉检测的交流磁轭 AC YOKE MAGNET FOR MAGNETICPARTICLE TESTING

JIS Z 2340:2002 磁粉和渗透检验中目视校验计较准方法的确认

Confirmation method of calibration by visual calibration gauge on magneticparticle and liquid penetrant testing

JIS Z 2343-3:2001 无损检测渗透检测第3部分：参考试块

Non-destructive testing -- Penetrant testing -- Part 3: Reference test blocks

JIS Z 8202-5-2000 量值和单位第5部分:电学和磁学 Quantities and units - Part 5: Electricity and magnetism

JIS W 1202-1986 宇航用涡流法对铝合金热处理测量的电导试验

Electrical conductivity test for measurement of heat treatment of aluminumalloys, eddy current method, for aerospace use

JIS W 4031-82 宇航用磁粉检验方法 INSPECTION PROCESS OF MAGNETICPARTICLE FOR AEROSPACE USE

NDIS 3101-84 涡流探伤装置单项性能的测试及其表示方法

NDIS 3102-84 涡流探伤装置综合性能的测试及其表示方法

NDIS 3301-77 磁粉探伤用C1型标准试片

NDIS 3404-82 漏磁探伤测试方法(INDT,85-3)

NDIS 3105-83 交流磁轭磁粉检验装置性能与试验方法

NDIS 3403-81 表面缺陷检测方法

03014008发表于 2008-11-812:55

德国标准：

DIN 50470-1980 永磁材料的检测测定磁轭的退磁曲线和永磁导磁率感应法

Testing of permanent magnet materials; Determination of the demagnetizationcurve and permanent permeability in a yoke; Inductive method

DIN 50472-1981 永久磁铁的检测在工作范围内测定磁通量值

Testing of permanent magnets; determination of the magnetic flux values in theworking range

DIN 50933-1987 用探针式差动测量器测量涂层厚度

Measurement of coating thickness by differential measurement using a stylusinstrument

DIN 50981-79 用磁粉法测量铁素体材料非铁磁性层的厚度

DIN 50984-78 用涡流法测量非铁素体母材的非导电层厚度

DIN 50985-77 用电容法测量导电母材上非导电层的厚度

DIN 54121-65 磁粉探伤定义及检验证明

DIN 54130-1974 无损检测漏磁检测通则

Non-destructive testing; magnetic leakage flux testing, general

DIN 54131T1-84 除携带式以外的固定式与移动式磁粉检验设备性能及测定方法

DIN 54131T2-84 携带式磁粉检验设备性能及测定方法

DIN 54132-80 磁粉检验介质的性能测定

DIN 54136-1-1988 无损检测带扫描探头的漏磁检测原理

Non-destructive testing; magnetic leakage flux testing by scanning with probes;principles

DIN 54140-3-1989 无损检测电磁法测试线圈组件的图像和一般特性

Non-destructive testing; electromagnetic methods; representation and generalcharacteristics of test coil assemblies

DIN 54140T1-76 电磁(涡流)法检测的一般规则

DIN 54140T2-84 电磁检测名词术语

DIN 54141-1-1982 无损检测管子的涡流检测用同心试验线圈和单频率法检测的一般注意事项

Non-destructive testing; Eddy current testing of pipes and tubes; Generalremarks on testing using concentric test coils and the single-frequency method

DIN 54141-2-1982 无损检测管子的涡流检测同心试验线圈的涡流检测系统性能测定与校验的参考方法Non-destructive testing; Eddy current testing of pipes and tubes; Referencemethod for the determination and calibration of the properties of an eddycurrent testing system using concentric test coils

DIN 54141-3-1987 无损检测管子的涡流检测方法

Non-destructive testing; eddy current testing of pipes and tubes; procedure

DIN 54141T1-82 穿过式线圈单频法管材涡流检测(NDT,86-1)

DIN 54141T2-82 穿过式线圈涡流检验装置性能的测定方法

DIN 54141T3-85 涡流检测的实施

DIN 25435T2-79 核技术设备定期磁粉检验

DIN V VDE V 0848-4/A3-1995 电磁场中的安全性在0至30KHz频率范围的人员防护修订3

Safety in electromagnetic fields - Protection of persons in the frequency rangefrom 0 to 30 kHz; Amendment A3

DIN EN 1290-2002 焊缝的无损检测焊缝的磁粉检测

Non-destructive testing of welds - Magnetic particle testing of welds; Germanversion EN 1290:1998 + A1:2002

DIN EN 1291-2002 焊缝的无损检测焊缝的磁粉检测验收等级

Non-destructive testing of welds - Magnetic particle testing of welds -Acceptance levels; German version EN 1291:1998 + A1:2002

DIN EN 1330-5-1998 无损检测术语第5部分:涡流检测

Non-destructive testing - Terminology - Part 5: Terms used in Eddy Currenttesting; trilingual version EN 1330-5:1998

DIN EN 1369-1997 铸造磁粉检验 Founding - Magnetic particleinspection; German version EN 1369:1996

DIN EN 1971-1998 铜和铜合金管子的涡流检测

Copper and copper alloys - Eddy current test for tubes; German version EN1971:1998

DIN EN 1711-2000 焊缝的无损检验焊缝的复平面分析涡流检验

Non-destructive examination of welds - Eddy current examination of welds bycomplex plane analysis; German version EN 1711:2000

DIN EN 10228-1-1999 钢锻件的无损检测第1部分:磁粉检验

Non-destructive testing of steel forgings - Part 1: Magnetic particleinspection; German version EN 10228-1:1999

DIN EN 10246-1-1996 钢管的无损检测第1部分:验证无缝和焊接铁磁钢管(埋弧焊除外)水压密封性的自动电磁检测 Non-destructive testing of steel tubes - Part 1: Automatic electromagnetictesting of seamless and welded (except submerged arc-welded) ferromagneticsteel tubes for verification of hydraulic leak-tightness; German version EN10246-1:1996

DIN EN 10246-3-2000 钢管的无损检测第3部分:探测无缝和焊接钢管(埋弧焊接除外)不完整性的自动涡流检测Non-destructivetesting of steel tubes - Part 3: Automatic eddy current testing of seamless andwelded (except submerged arc-welded) steel tubes for the detection ofimperfections; German version EN 10246-3:1999

DIN EN 10246-4-2000 钢管的无损检测第4部分:探测铁磁无缝钢管横向不完整性的自动全圆周磁探头/磁漏检测 Non-destructive testing of steel tubes - Part 4: Automatic fullperipheral magnetic transducer/flux leakage testing of seamless ferromagneticsteel tubes for the detection of transverse imperfections; German version EN10246-4:1999

DIN EN 10246-5-2000 钢管的无损检测第5部分:探测无缝和焊接(埋弧焊接除外)铁磁钢管纵向不完整性的自动全圆周磁探头/磁漏检测 Non-destructive testing of steel tubes- Part 5: Automatic full peripheral magnetic transducer/flux leakage testing ofseamless and welded (except submerged arc-welded) ferromagnetic steel tubes forthe detection of longitudinal imperfections; German version EN 10246-5:1999

DIN EN 10246-18-2000 钢管的无损检测第18部分:探测无缝和焊接铁磁钢管管端层状不完整性的磁粉检验 Non-destructivetesting of steel tubes - Part 18: Magnetic particle inspection of the tube endsof seamless and welded ferromagnetic steel tubes for the detection of laminarimperfections; German version EN 10246-18:2000

DIN EN 12084-2001 无损检测涡流检测一般原理和基本指南

Non-destructive testing - Eddy current testing - General principles and basicguidelines; German version EN 12084:2001

DIN EN 13860-1-2003 无损检测涡流检验设备特性和验证第1部分:仪器特性和验证

Non-destructive testing - Eddy current examination; Equipment characteristicsand verification - Part 1: Instrument characteristics and verification; Germanversion EN 13860-1:2003

DIN EN 13860-2-2003 无损检测涡流检验设备特性和验证第2部分:探头特性和验证

Non-destructive testing - Eddy current examination; Equipment characteristicsand verification - Part 2: Probe characteristics and verification; Germanversion EN 13860-2:2003

DIN EN ISO 2178-1995 磁性基体上的非磁性涂镀层涂镀层厚度测量磁性法

Non-magnetic coatings on magnetic substrates - Measurement of coating thickness- Magnetic method (ISO 2178:1982); German version EN ISO 2178:1995

DIN EN ISO 2360-1995 非磁性基体金属上的非导体涂层涂层厚度测量涡流法

Non-conductive coatings on non-magnetic basis metals - Measurement of coatingthickness - Eddy current method (ISO 2360:1982); German version EN ISO2360:1995

DIN EN ISO 2361-1995 磁性和非磁性基体上的镍电镀层镀层厚度测量磁性法

Electrodeposited nickel coatings on magnetic and non-magnetic substrates -Measurement of coating thickness - Magnetic method (ISO 2361:1982); Germanversion EN ISO 2361:1995

DIN EN ISO 9934-1-2002 无损检测磁粉检测第1部分:一般原理

Non-destructive testing - Magnetic particle testing - Part 1: Generalprinciples (ISO 9934-1:2001); German version EN ISO 9934-1:2001

DIN EN ISO 9934-2-2003 无损检测磁粉检测第2部分:探测介质

Non-destructive testing - Magnetic particle testing - Part 2: Detection media(ISO 9934-2:2002); German version EN ISO 9934-2:2002

DIN EN ISO 9934-3-2002 无损检测磁粉检测第3部分:设备

Non-destructive testing - Magnetic particle testing - Part 3: Equipment (ISO9934-3:2002); German version EN ISO 9934-3:2002

03014008发表于 2008-11-812:57

英国标准：

BS 1881-204-1988 混凝土试验-电磁式保护层厚度计应用的推荐方法

BS 3680/3H:1993 利用线圈全部长、宽的电磁方法

BS 3683-2-1985 无损检测术语磁粉探伤

Glossary of terms used in non-destructive testing - Magnetic particle flawdetection

BS 3683 Pt.5-83 涡流检测名词术语

BS 3889 Pt.2A-86(1991) 管道和管子无损检测方法锻钢管的涡流检测

BS 3889 Pt.2B-82管道和管子无损检测方法有色金属管的涡流检测

BS 4069-82 磁粉探伤用磁粉及磁悬液(INDT,84-2)

BS 4080/1: 用磁粉探伤显示表面缺陷

BS 4397-69 焊缝的磁粉检测方法(WSTS,85-4)

BS 4408 Pt.1-69 混凝土复盖层的电磁测量方法

BS 4489:1984 无损检测中评定黑光的方法

BS 5044-73(1987) 磁粉探伤用反差增强涂料

BS 5138-74(2000) 精加工整体锻造及落锤锻曲轴的磁粉检验

BS 5411 Pt.3-84 非磁性基体上非导电复盖层厚度的涡流检测

BS 5411 Pt.9-84 非磁性基体上镀镍层厚度的磁性检测方法

BS 5411 Pt.11-84磁性基体上非磁性复盖层厚度的磁性测量方法

BS 6072-81(1986) 缺陷的磁粉检验方法(81年版在INDT 84-2)

BS 6404-5-1995 磁性材料永磁(硬磁)材料磁性能测量方法

Magnetic materials - Permanent magnet (magnetically hard) materials - Methodsof measurement of magnetic properties

BS DD ENV 50166-1-1995 人体电磁场照射低频(0 Hz 至 10 kHz)

Human exposure to electromagnetic fields - Low frequency (0 Hz to 10 kHz)

BS DD ENV 50166-2-1995 人体电磁场照射高频(10 kHz 至 300 GHz)

Human exposure to electromagnetic fields - High frequency (10 kHz to 300 GHz)

BS M35 材料及工件的磁粉检验

BS EN 1290-1998 焊缝的无损检验焊缝的磁粉检验

Non-destructive examination of welds - Magnetic particle examination of welds

BS EN 1291-1998 焊缝的无损检验焊缝的磁粉检验验收等级

Non-destructive examination of welds - Magnetic particle testing of welds -Acceptance levels

BS EN 1330-5-1998 无损检测术语-涡流检测Non-destructive testing - Terminology - Terms used in eddy current testing

BS EN 1369-1997 铸造-磁粉检验Founding - Magnetic particle inspection

BS EN 10228-1-1999 锻钢件无损检测-磁粉检验Non-destructive testing of steel forgings - Magnetic particle inspection

BS EN 10246-1-1996 钢管的无损检测-铁磁性无缝与焊接（埋弧焊除外）钢管验证水压试验的自动电磁检测

Non-destructive testing of steel tubes - Automatic electromagnetic testing ofseamless and welded (except submerged arc welded) ferromagnetic steel tubes forverification of hydraulic leak-tightness

BS EN 10246-2-2000 钢管的无损检测-奥氏体与奥氏体-铁素体无缝与焊接（埋弧焊除外）钢管验证水压试验的自动涡流检测

BS EN 10246-3-2000 钢管的无损检测-探测无缝与焊接（埋弧焊除外）钢管不完整性的自动涡流检测

Non-destructive testing of steel tubes - Automatic eddy current testing ofseamless and welded (except submerged arc-welded) steel tubes for the detectionof imperfections

BS EN 10246-4-2000 钢管的无损检测-铁磁性无缝钢管横向不完整性自动全圆周磁探头/漏磁检测

Non-destructive testing of steel tubes - Automatic full peripheral magnetictransducer/flux leakage testing of seamless ferromagnetic steel tubes for thedetection of transverse imperfections

BS EN 10246-5-2000 钢管的无损检测-铁磁性无缝与焊接（埋弧焊除外）钢管纵向不完整性自动全圆周磁探头/漏磁检测 Non-destructive testing of steel tubes- Automatic full peripheral magnetic transducer/flux leakage testing ofseamless and welded (except submerged arc-welded) ferromagnetic steel tubes forthe detection of longitudinal imperfections

BS EN 10246-12-2000 钢管的无损检测探测无缝和焊接铁磁钢管表面不完整性的磁粉检验

Non-destructive testing of steel tubes - Magnetic particle inspection ofseamless and welded ferromagnetic steel tubes for the detection of surfaceimperfections

BS EN 10246-18-2000 钢管的无损检测探测无缝和焊接铁磁钢管管端层状不完整性的磁粉检验

Non-destructive testing of steel tubes - Magnetic particle inspection of tubeends of seamless and welded ferromagnetic steel tubes for the detection oflaminar imperfections

BS EN 12084-2001 无损检测-涡流检测-一般原理与指南

Non-destructive testing - Eddy current testing - General principles andguidelines

BS EN ISO 2178-1995 磁性基体上非磁性涂层的厚度测量-磁性法

Non-magnetic coatings on magnetic substrates - Measurement of coating thickness- Magnetic method

BS EN ISO 2360-1995 非磁性金属基体上非导电涂层的厚度测量-涡流法

Non-conductive coatings on non-magnetic basis metals - Measurement of coatingthickness - Eddy current method

BS EN ISO 2361-1995 磁性和非磁性基体上镍镀层的厚度测量-磁性法

Electrodeposited nickel coatings on magnetic and non-magnetic substrates -Measurement of coating thickness - Magnetic method

BS EN ISO 9934-1-2001 无损检测磁粉检测一般原理 Non-destructivetesting - Magnetic particle testing - General principles

BS EN ISO 9934-2-2002 无损检测磁粉检测探测介质 Non-destructive testing -Magnetic particle testing - Detection media

BS EN ISO 9934-3-2002 无损检测磁粉检测设备 Non-destructive testing -Magnetic particle testing - Equipment

03014008发表于 2008-11-812:58

法国标准：

NF A04-101-64 冶金产品磁粉检测(磁悬液检测)

NF A04-121-74 钢制长条形制品表面缺陷的磁粉检验

NF A04-193-1997 铸造磁粉检验 Founding - Magnetic particleinspection.

NF A05-115-1999 铜及铜合金管子的涡流检测 Copper and copper alloys.Eddy current test for tubes.

NF A09-020-5-1998 无损检测术语第5部分:涡流检测

Non-destructive testing. Terminology. Part 5 : terms used in Eddy Currenttesting.

NF A09-125-82 冶金制件磁粉探伤的一般原理

NF A09-160-2001 无损检测涡流检测一般原理和指南

Non-destructive testing - Eddy current testing - General principles andguidelines.

NF A09-590-1-2002 无损检测磁粉检测第1部分:一般原理

Non-destructive testing - Magnetic particle testing - Part 1 : generalprinciple.

NF A09-590-3-2002 无损检测磁粉检测第3部分：设备

Non-destructive testing - Magnetic particle testing - Part 3 : equipment.

NF A49-871-81 铁磁性钢管纵向缺陷的探头检漏法检测

NF A49-872-83 穿过式线圈法的钢管涡流探伤

NF A49-875-1-1996 钢管的无损检测第1部分:无缝和焊接铁磁钢管(埋弧焊除外)验证水压试验的自动电磁检测Non destructive testing of steels tubes. Part 1 : automatic electromagnetictesting of seamless and welded (except submerged arc welded) ferromagneticsteel tubes for verification of hydraulic leak-tightness.

NF A49-875-2-2000 钢管的无损检测第2部分:无缝和焊接奥氏体和奥氏体铁素体钢管(埋弧焊除外)验证水压试验的自动涡流检测Non-destructive testing of steel tubes - Part 2 : automatic eddy currenttesting of seamless and welded (except submerged arc-welded) austenitic andaustenitic-ferritic steel tubes for verification of hydraulic leak-tightness.

NF A49-875-3-2000 钢管的无损检测第3部分:探测无缝和焊接钢管(埋弧焊除外)不完整性的自动涡流检测Non-destructive testing of steel tubes - Part 3 : automatic eddy currenttesting of seamless and welded (except submerged arc-welded) steel tubes forthe detection of imperfections.

NF A49-875-4-2000 钢管的无损检测第4部分:探测无缝铁磁钢管横向不完整性的自动全圆周磁探头/磁漏检测 Non-destructive testing of steel tubes- Part 4 : automatic full peripheral magnetic transducer/flux leakage testingof seamless ferromagnetic steel tubes for the detection of transverseimperfections.

NF A49-875-5-2000 钢管的无损检测第5部分:探测无缝和焊接(除埋弧焊)铁磁钢管纵向不完整性的自动全圆周磁探头/漏磁检测 Non-destructive testing of steel tubes- Part 5 : automatic full peripheral magnetic transducer/flux leakage testingof seamless and welded (except submerged arc welded) ferromagnetic steel tubes forthe detection of longitudinal imperfections.

NF A49-875-12-2000 钢管的无损检测第12部分:探测无缝和焊接铁磁钢管表面不完整性的磁粉检验

Non-destructive testing of steel tubes - Part 12 : magnetic particle inspectionof seamless and welded ferromagnetic steel tubes for the detection of surfaceimperfections.

NF A49-875-18-2000 钢管的无损检测第18部分:探测无缝和焊接铁磁钢管管端层状不完整性的磁粉检验 Non-destructive testing of steel tubes - Part 18 : magneticparticle inspection of tube ends of seamless and welded ferromagnetic steeltubes for the detection of laminar imperfections.

NF A89-550-1998 焊缝的无损检验焊缝的磁粉检验

Non-destructive examination of welds - Magnetic particle examination of welds.

NF A89-550/A1-2002 焊缝的无损检测焊缝的磁粉检测

Non-destructive testing of welds - Magnetic particle testing of welds.

NF A89-551-1998 焊缝的无损检验焊缝的磁粉检测验收等级

Non-destructive examination of welds - Magnetic particle testing of welds -Acceptance levels.

NF A89-551/A1-2002 焊缝的无损检测焊缝的磁粉检测验收等级

Non-destructive testing of welds - Magnetic particle testing of welds -Acceptance levels.

NF A91-112-1995 磁性基体上的非磁性涂层涂层厚度测量磁性法

Non-magnetic coatings on magnetic substrates. Measurement of coating thickness.Magnetic method.

NF A91-113-1995 非磁性基体金属上的非导电涂层涂层厚度测量涡流法

Non-conductive coatings on non-magnetic basis metals. Measurement of coatingthickness. Eddy current method.